The SMLIGHT Ultima, a butter knife and an old remote

SMLIGHT SLZB-Ultima 3 • Home Assistant • Zigbee • Thread • PoE

Quick Take

The Ultima 3 runs Zigbee and Thread side by side. It also has Bluetooth, IR, lights and a buzzer in the same, smaller than expected, plastic enclosure. The extras are why I would buy it over the MR5U or something else in the SMLIGHT lineup. I use the lights to see if Zigbee2MQTT is running in Home Assistant and an old IR remote to control the house. If you just want Zigbee and Thread with PoE built in, I’d buy the MR5U. If you just need a USB Zigbee stick, I’d start with the SLZB-07.

I bought a used PoE switch on eBay a few months ago for another project I haven’t gotten to yet. It sat there until I decided to open the SMLIGHT Ultima with Mom’s butter knife, my tool of choice since long before any home was made smart.

This went about as well as you might expect. I put a couple little scratches in the case and spent the whole time thinking I was about to destroy it. Once the case opened, I chilled out and pressed the little PoE board into place. I spent way longer rearranging the mess behind my TV to accommodate the switch than I did installing the module.

I’d never actually used PoE before. The idea is simple enough, but it was still a little weird to plug in one Ethernet cable and watch the Ultima light right up. Zigbee came back. I played a little RTTTL Mario Bros on the buzzer to make sure that still worked too.

I might actually love PoE. It’s hard to describe but it felt less plugged in.

SMLIGHT Ultima 3 with both antennas extended, between a butter knife and an old Vizio soundbar remote.
The SMLIGHT Ultima 3 with Mom’s butter knife and the old soundbar remote.

I moved my Zigbee network again

My SLZB-07 USB stick worked for years and reached all the way to my detached garage. This summer, I tried the Nano as a hub for a little network before moving it to a friend’s house to manage remotely. Then I moved my main network to the MR5U and added a Thread border router.

I added the Ultima to Home Assistant in September, and the Zigbee move went smoothly again, just like when I moved to the MR5U. Radio 1 took over the same Zigbee network. Done.

Thread gave me a little more pause. Matter loaded in Home Assistant after the swap, but Home Assistant showed zero Thread border routers. A restart seemed to do the trick. The Ultima showed up as a border router on Radio 2, and I didn’t have to re-pair any of my Matter devices.

Yes, I’d buy it just for the lights

The Ultima’s front LEDs change from a moving rainbow to alternating red and blue, then return to rainbow as the animation loops.
LED effects demo. Rainbow switches to Police to indicate an issue with Zigbee.

The Ultima normally runs a rainbow effect at my house. I liked that one best. I’ve also worked the LEDs into my lighting scenes and nighttime routine. It’s in my living room, so why not. If Zigbee2MQTT stops in Home Assistant and the Ultima is still on Ethernet, they switch to the Police effect. When Zigbee2MQTT comes back, so does the rainbow. I can see something’s up from across the room without opening a dashboard.

There’s also a buzzer. I’m testing a sleep lamp that uses several bed related sensors, so I set up a different little RTTTL tune for getting into and out of bed. I hear it and think, yep, that’s working. It’s a subtle cue I can use without pulling out my phone or making a TTS announcement, which I’ve also been known to do.

Zigbee and Thread are enough to justify SMLIGHT in my house. The lights are enough to make me pick this particular box over another MR5U. The buzzer makes it even easier.

I rediscovered the remote control

I tried two AC units. With the first, the Ultima picked up the remote, but the learner kept saying the code was unknown or incomplete. SMLIGHT said AC remotes can use longer, more complicated codes and gave me a few things to try. With a different AC, I captured a command and replayed it through MQTT. The AC didn’t respond, even with the Ultima pointed right at it. Then I tried the TV. The power command turned it on and off just fine.

The thing I kept using was a soundbar remote (pulled from the Ziploc bag where all the remotes live). The Ultima listens for the buttons and Home Assistant runs automations accordingly. Now the remote changes light scenes, adjusts brightness and controls my music. I have to avoid mute and power because the newer soundbar is the same brand as another and hears those too. I also learned that scrolling through a bunch of scenes is kind of a hassle. I’d much rather give each scene its own button.

I’m on the lookout for a thrift store remote with more buttons but start with your junk drawer. IR is also a great way to control existing and older hardware with your smart home.

A few things I found inside

The case is the part I wish SMLIGHT had made easier to open, especially because it’s designed to be modular. A plastic pry tool would probably have saved me a couple scratches. The PoE board itself just presses in. I also noticed three tiny recessed buttons. One restarts the device, and I’d reach for a toothpick to press them. Awkward as an everyday control.

Open SMLIGHT Ultima 3 board with callouts pointing to the Ethernet jack and the installed PoE board.
The Ethernet jack and installed PoE board inside the SMLIGHT Ultima 3.

The Z-Wave and LTE boards SMLIGHT sent are still reserved for future use. I am curious about the optional 433 MHz RF module. The walking pad in my office has a remote in that band, and of course I want to see if I can control it through an automation. I already have Zigbee, Thread, Bluetooth and IR in the same hub.

You can flash it with ESPHome

There’s an ESP32-S3 that runs the main firmware and handles things like networking, the LEDs and IR. Zigbee and Thread have their own radio chips with their own firmware. Flashing the ESP32 with ESPHome replaces SLZB-OS on that main chip. The radio firmware stays on its own chips. Your ESPHome configuration still needs to expose the radios the way your Zigbee and Thread setup expects, and some stock features work differently or are missing.

Everything I’ve described using day to day was on SLZB-OS. The Ultima shows up under Bluetooth in Home Assistant with scanning set to Auto and no connection slots. If I needed it to make active Bluetooth connections, I’d start with SMLIGHT’s ESPHome project. Right now, I’m happy using it as a hub, but I like having the option to run different firmware if my needs change.

Which SMLIGHT would I buy?

I love Home Assistant, but when it comes to buying a radio, I’m team SMLIGHT. I see the Connect ZBT-2 recommended all the time in online communities, but plenty of people go the SMLIGHT route too. The ZBT-2 gives you Zigbee or Thread over USB, one at a time. I want both running at once and the freedom to put my radios wherever I can run Ethernet or even put them on Wi-Fi if I want, my choice. I’d buy the MR5U for that alone. The Ultima’s extras are why I’d buy it for my house.

I’d group SMLIGHT options into three price tiers. The base Ultima can overlap with Tier 2, especially if you’re shopping around. Bundles with extra modules are where it moves into Tier 3.

Model What I’d buy it for Price tier
SLZB-07 USB family A Zigbee radio for the machine you already run. Tier 1
SLZB-MR5U A network coordinator with separate Zigbee and Thread radios and PoE built in. Tier 2
SMHUB Nano MG24 A little Linux box that runs Zigbee2MQTT and Node-RED itself. Remote/standalone. Tier 2
SLZB-Ultima 3 Zigbee and Thread plus Bluetooth, IR, lights, a buzzer and optional modules. Tier 2 overlap for the base unit. Tier 3 for bundles.

At my house the Ultima is doing all the boring stuff the MR5U did so well. It’s also blinking at me when Zigbee2MQTT disconnects, making little noises while I test automations and giving me a reason to dig through the remotes at the thrift store. And somehow it’s the thing that finally got me to plug in that damn switch.

Comments